CALL US: 1-800-445-0624
Showing: 1-20 of 24    »»
Articles
 
document Body blower fan on PL69 operating at all times.
The body-blower fan on the Ergoline Ambition, Soltron, Kiss or Flirt may operate at all times if the power wires of the fan become pinched between the fan housing and the end cap of the tanning system during installation. This situation can cause the wires to short together and create and...
rating 17 Dec, 2012 Comments: 0
document E131
E131 : System message: data communication additional controller If the additional controller receives no data from the main controller then the sunbed switches off with this system message. Causes for this can be a defective main board or a software problem.
rating 13 Dec, 2012 Comments: 0
document Ergoline, Soltron timer displaying Err.
By design the Ergoline and Soltron tanning systems deliver the "Err" message when: An incorrect access code has been entered.   If the display appear as `- - - - `, this is incorrect and the procedure must be repeated. The salon owner has changed the access code and...
rating 10 Dec, 2012 Comments: 0
document General Information: Aqua Fresh/Vitalizer Kit (TAM 599)
The Aqua Fresh/Vitalizer products for use in Ergoline and Soltron units has been repackaged to include the following items. 1          Essence 1 ea.   Customized Label, Contents Label (USA only), Info. Tag, User's...
rating 17 Dec, 2012 Comments: 0
document General Information: Freight Damage Policy and Claim Procedure
JK|Products and Services is not responsible for shipments received damaged that are not noted as damaged when signed for. Please inspect all shipments from JK|Products and Services for damage both to the packaging and the the contents.  If damage is found, have the damage noted before...
rating 29 Dec, 2012 Comments: 0
document General Information: How to interrupt tanning session
Yes. All units manufactured by JK Products and Services are equiped with a display console that is cabable of being accessed by the user while they are using the tanning unit.  In general, the session can be interruped by pressing and holding the Stop or Start/Stop button...
rating 18 Dec, 2012 Comments: 0
document General Information: Order Return Policy and Procedure
The following policies apply to new parts purchased from JK Global Service via sales, support, or service representatives as well as by electronic means. 1. Parts are guaranteed to be free of defect or damage for thirty (30) day from the date of purchase. Warranty claims...
rating 29 Dec, 2012 Comments: 0
document General Information: Replacing Your Intelitan CCS Controler
There are no issues replacing your old CCS controler with a new CCS contoler.  When replacing, your network cable should be disconnected from the old controler and connected to the new one before powering on the new one.  Once powered on your units should automatically be...
rating 29 Dec, 2012 Comments: 0
document General Information: Setting Parameters from Intellitan CCS III / IV Controler
You can view or send parameters to individual tanning units via entering your 3rd level password and choosing either the get params or send params option depending on the function you are wanting to perform.  Example: Press "Call/Menu" "<3rd Level Password>" and then...
rating 13 Dec, 2012 Comments: 0
document General Information: V33/V42 Processor Chip Compatability
No.  The V42 and V33 chips will not interchange. Only the version V37 is interchangable with the V42 chip used on later models of the Intellitan Power Boards. On the earlier models of the Intellitan Power Boards, the V23 through the V33 chips are interchangeable. ...
rating 29 Dec, 2012 Comments: 0
document General Information: Why is my Intellitan Plus timer displaying "8888"?
The Intellitan Plus timer found on the Sun|Dash series tanning units will display "8888" if the software becomes corrupt or if the main processor fails. The Intellitan timer may become corrupt if it receives an electrical surge during power up or operation.  You may attempt...
rating 29 Dec, 2012 Comments: 0
document Installation Instructions: Voltage requirements for Intelitan Console Timer
This console timer is rated to operate optimally at 120 volts.  If your timer is receiving voltage which falls outside of a range from 108 to 130 volts you may experience undesirable operation and/or failure of the timer. At no time should this timer be connected to any service that...
rating 29 Dec, 2012 Comments: 0
document Issue: Intelitan counts down but bed does not start
If the remote timer is counting down but the unit does not turn on try the following to resolve the sititutation: Swap the wires located at positions S3 and N (white and black). Test for voltage beween the following pairs of wires with the timer in stand-by mode and verify the...
rating 31 Dec, 2012 Comments: 0
document Issue: Network Problems and Power / Timer Boards
YES At times a bad power board or timer in a salon's network can cause problems. Units can drop off the network, not show up at all, or even appear / disappear. At times the unit might run fine off the network but when added cause problems to return.
rating 11 Dec, 2012 Comments: 0
document Issue: Remote "Black Box" timer not responding (locked)
The timer may be locked up. To unlock push all four buttons at the same time. You should then be able to operate timer. If after performing this procedure the unit does not unlock, a replacement may be necessary.  Please contact your local JK technician of parts representative for...
rating 29 Dec, 2012 Comments: 0
document Network Setup: Intellitan CCS or T-Max Manager Master/Slave Configuration
All programming will need to be done in the third security, or manager, level. Press "Call/Menu" and "Enter" your third level password (be default "300" on a CCS and "3333" on T-Max) Press "Next" until you reach MGR PARAMS and press "Enter" Set "MANAGER...
rating 29 Dec, 2012 Comments: 0
document Parameters: Intelitan "Black Box" Remote Timer Parameters
The following is a list of parameters available on the Intelitan "Black Box" remote timer. P02    Alarm Enable/Disable function P03     Station Address P04     Lamp Hour Accumulation P05     Session...
rating 29 Dec, 2012 Comments: 0
document Timer Displaying "88"
The Intellitan timer found on the Sun|Dash series tanning units will display "88" if the software becomes corrupt or if the main processor fails. The Intellitan timer may become corrupt if it receives an electrical surge during power up or operation.  You may attempt to...
rating 10 Dec, 2012 Comments: 0
document type of power supply required for DMS music interface module.
A 12V DC power supply is required to operate the DMS music interface module.
rating 17 Dec, 2012 Comments: 0
document Unit Information: Converting either a Intelitan CCS IV or TMax Manager Pro
You can convert your Intellitan CCS IV to a TMax Manager Pro or TMax manager Pro to a CCS IV by downloading the appropriate software to the unit.  Please download the software for what you want to convet the unit to by following the link below: NOTE:  You must have...
rating 29 Dec, 2012 Comments: 0

Showing: 1-20 of 24    »»

RSS

Contraindication: This product is contraindicated for use on persons under the age of 18 years. "Contraindication: This product must not be used if skin lesions or open wounds are present." "Warning: This product should not be used on individuals who have had skin cancer or have a family history of skin cancer." "Warning: Persons repeatedly exposed to UV radiation should be regularly evaluated for skin cancer.